Shop for American DJ V Power Amplifier and more at everyday discount prices with free shipping over $50* on – Your Online Store!. Buy the ADJ V Amplifier at PlanetDJ. Low VIP Pricing, Financing and Free Shipping available. American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power.
|Published (Last):||2 June 2007|
|PDF File Size:||4.26 Mb|
|ePub File Size:||5.69 Mb|
|Price:||Free* [*Free Regsitration Required]|
Carefully check the shipping carton for damage that may have occurred during shipping. Connect an input signal to channel one. The fixture does not appear to operate normally or exhibits a marked change in performance. This LED may glow when the unit has been turned off, this is normal. No user serviceable parts inside. Be sure that your front gain controls are turned down to their lowest level full counter-clockwise. This symbol is intended to alert the user v0300 the presence of important operating and maintenance servicing instructions in the literature accompanying the product.
American Audio Stereo Amplifier V/V User Guide |
A sj circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself. To reset the breaker, push it in.
When constructing your own XLR cables follow the pin configuration describe below for proper connections. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible.
The power-supply cord or the plug has been damaged. Connect a XLR cable to the input of channel one. When dip switches 2 and 3 are in the “ON” amerocan filter will cut off frequencies at and below 30Hz, when these dip switches are in the “OFF” position the filter will cut off frequencies at and below 50Hz.
American DJ V3000 2 Channel Professional Stereo Amplifier
If the input gain level is not reduced the built-in americann will activate. Use the channel one gain to regulate your amplifier output. Channel 2 Gain Control – This rotary knob is used to control the output signal of channel two. Channel 1 filters is control by dip switch 1 and channel 2 filter is controlled by dip switch 4. Use these connections to connect the aemrican signal from a mixer, cross-over or EQ to your V Vplus series amplifier.
American Audio V3000/V2000 Stereo Amplifier User Manual
Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack. Clipping should be kept to a reasonable minimum. When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction. A limiter takes the gain of an overloading signal and reduces it, the d in gain reduces distortion that can cause damage to your speakers and amplifier.
Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.
Insert bare wire into the binding post and tighten. Please do not return the amplifier to your dealer without contacting customer support.
To reduce the risk of electrical shock, do not remove cover. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.
This fans are used to cool the internal parts of the amplifier when in use. Risiko – Elektrischer Schlag! The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the user manual accompanying the amplifier.
The dip amefican on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either a 50Hz or 30 Hz cut-off. After inserting the wire into the binding post hole, screw the binding post cap down on the wire. See page 9 for more details on input configuration. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping.
During low level output the fans run at normal speeds. The Output Short Circuit Protection protects the output devices of the amplifier from anerican circuits and stressful loads. Short Circuit Protection can usually be traced back to the signal output line i.
Configuring the Low Cut Filter: Connect your inputs into channels one and two of the amplifier. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Dieses Symobl soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen.
Gain Controls – V0300 gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. Under heavy clipping activity lower the channel one gain control to reduce the risk of damage to your speakers and amplifier.
American Audio V User manual |
Amplifiers arrive to you preset in the wmerican operation mode. An ultrasonic network uncouples RF from the output and helps keep the amplifier stable with reactive loads. The appliance has been exposed to rain or water. Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response.