Baixe grátis o arquivo ASTM Apdf enviado por DANIEL no curso de Engenharia Mecânica. Sobre: Astm a ASTM A/AM(98), Austenitic, corrosion resistant, solution quenched and aged. 21 Sep Articles. Microstructure and Mechanical Properties of ASTM A CA6NM Steel Welded by.

Author: Tausho Shale
Country: Turkmenistan
Language: English (Spanish)
Genre: Love
Published (Last): 17 April 2016
Pages: 368
PDF File Size: 2.95 Mb
ePub File Size: 1.90 Mb
ISBN: 531-3-71788-366-3
Downloads: 91712
Price: Free* [*Free Regsitration Required]
Uploader: Gardalmaran

To see MatWeb’s complete data sheet for this material including material property data, metal compositions, material suppliers, etcplease click the button below.

Thus, both joints would be approved in accordance to this criterion. The microstructure and mechanical properties of the as-welded joint was compared to a joint which suffered a post welding heat treatment PWHT.

Despite nearly identical toughness values of the weld metal from AW and PWHT samples, results of fracture analysis have shown distinct features in appearance of the fractures as depicted in Figure 12 and Figure Welding Metallurgy of Stainless Steels. Results and Discussions Figure 5 illustrates mosaics of the weld joints obtained by using a motorized optical microscope OM.

It should be pointed out that toughness is the most important property in the qualification process of a welded joint of CA6NM steel and has a minimum value of 27J. According to the manufacturer, the material was produced in an electric arc furnace, refined using an AOD furnace Argon Oxygen Decarburization and cast in sand molds as blocks of xx45 mm dimensions.

The samples were used in the form of flat specimens. Click here to view all the property values for this datasheet as they were originally entered into MatWeb. Property Data This page displays only the text of a material data sheet. Services on Demand Journal. Data sheets for overmetals, plastics, ceramics, and composites.

It is interesting to observe that results from the weld metal for both conditions are essentially the same, near 27 J, indicating that PWHT does affect significantly this property in spite of lower hardness values presented by the material in this condition. The contents, 7a43, and technical data from this site may not be reproduced either electronically, photographically or substantively without permission from MatWeb, LLC.


Low toughness reduces the life of the piece and accelerates the process of cavitation as well astmm. Regions R and C present a more refined microstructure compared to the upper region Tlikely associated to a larger number of heat cycles suffered by these regions as consequence of the greater number of weld passes over these regions.

Cast Grade: CF16a

The plate was cut into four strips of atm mm which were then machined to make chamfers for X shaped welds, as shown in Figure 1.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not wstm as part of the standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Austenitic, corrosion resistant, solution quenched and aged Key Words: The weld joints were free of defects such as cracks, porosity, slag entrapment, lack of fusion and incomplete penetration.

We appreciate your input. Science and Technology of Welding and Joining. HAZ heat affected zone and weld metal WM at surface and center.

Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units.

Figure 4 illustrates the location of the microhardness xstm, including the base metal, weld metal and heat-affected zone.

How to cite this article. CA6NM steel is widely used in the manufacture of hydraulic turbines metallic parts, due to its resistance to corrosion and aztm damage, combined with good weldability and fatigue properties. Microhardness Vickers measurements were carried out in a Buehler MicroMet model using an applied load of gf for 30 seconds.


The PWHT hold time was chosen in order to be similar to a real large component stress relief treatment. Combining values from the two systems may result in nonconformance with the specification. In addition, a smoother hardness values distribution is observed among the different regions of the PWHT sample, making the hardness values of the weld metal close to those of base metal. This result is surprising considering the stress relieved microstructure and presence of retained austenite in ast, weld s743 of the PWHT material.

According to Bilmes et al.

ASTM A CF3M, L stainless steel casting – Magsen Foundry

The analysis were focused on four regions of each joint as indicated in Figure 3R rootC centerT top astk Z heat affected zone. This is an Open Access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

This specification covers iron-chromium and iron-chromium-nickel alloy castings for general corrosion-resistant application. Within the text, the SI units are shown in brackets.

ASTM A743 CF3M, 316L stainless steel casting

The reduction of the toughness, as well as the high residual stresses, can shorten the life of the pieceas well as accelerate the cavitation process. Or if you don’t have an account with us yet, then click here to register.

Please read our License Agreement regarding materials data and our Privacy Asym.

Posted in Sex