The LM is a high efficiency, step-up DC-DC switching regulator for battery- powered and low input voltage systems. It accepts an input voltage between V . Texas Instruments LM Series Switching Voltage Regulators are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas. Texas Instruments LM are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments LM
|Published (Last):||4 July 2010|
|PDF File Size:||4.40 Mb|
|ePub File Size:||16.55 Mb|
|Price:||Free* [*Free Regsitration Required]|
When I power on the device with a voltage less than 3. Aug 13, lm2621 In reply lm2621 Frank De Stasi: TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with lm2621 to these materials.
Then, R F2 can be selected using the above equation. In my board, I’m protecting the battery with a lm621. CH1 – Vin lm2621. Ask a new question Ask a new question Cancel. Lm2621 me know if this works. The LM’s high switching frequency enables the use of a small surface mount inductor.
LM V to V Input Voltage, Step-Up DC-DC |
The LM has now been move lm2621 a different group; so I do not know who lm2621 be answering questions about it. Aug 23, 1: Can you try lm621 your inductor value to 12uH?
For high lm2621, choose an inductor with a high frequency core material, such as ferrite, to reduce the core losses.
1.2-V to 14-V Input Voltage, Step-Up DC-DC
It looks like when you are at lower VIN, you lm2621 more, hence the higher current that lm26221 see on the input whereas when you at 4. The following section provides information regarding connection and component lm2621 to build a successful boost lm2621.
Lm2621 EN is tied to the ucontroller pin and the output of the pin is 3V. Table lm2621 shows a list of the diode manufacturers.
My Power Supply is lm2621 Li-Po battery with voltage range between 4. In reply to Bill Broach:. In order to successfully build an application, lm2621 designer should have the lm621 parameters:.
Content on this site may lm2621 or lm2621 subject to specific guidelines or limitations on use. No ripple, no noise, nothing.
LM2621 – High startup current
A high switching frequency allows the use of very small surface mount inductors and capacitors and results in a very small solution size. Lm2621 Search through millions of questions and lm2621 User. And lm2621 problem just disappear. TI and its respective suppliers and providers lm2621 content make no representations about the suitability lm2621 these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, lm2621 and non-infringement of any third party intellectual property right.
I still lm2621 the problem, but I think I could recognize the source of the problem.
LM データシート Low Input Voltage, Step-Up DC-DC |
If the problem still occurs, you can have a supervisory circuit or a power on reset connected lm2621 EN to disable the part when the Lm2621 is lower than 3V. See Design Requirements for the design requirement and following sections for the lm2621 design procedure. Lm2621 resistor values are selected as follows:. Lmm2621, Sorry for not providing further information regarding this thread.
To minimize radiated noise, use lm2621 toroid, pot core or shielded core inductor. This helps reduce the peak-to-peak output voltage ripple as well as improve the efficiency of the step-up regulator, because a set hysteresis of 30 mV at lm2621 FB pin is used for the gated oscillator control scheme.
So have you put the EN into its appropriate thereshold and lm2621 the issue?
Output voltage to set the feedback voltage divider and to assess the source for biasing the V DD pin. In reply lm2621 Arief Hernadi: In reply to Frank De Stasi:. Lm2621 newly created question will be automatically linked to this question. The LM is primarily used lm2621 a Lm2621 type lm2261 converter. It should have a DC working voltage rating higher than the maximum input voltage. In reply to Arief Hernadi:.
I’m working with lm2621 LM The resistor values are selected as follows: