Does anyone have a copy of the manual for the Eclipse 7 that is not missing pages 44 and 45, every PDF I have found goes pg 42,43,4,5,46, Hitec Eclipse 7 January 17, Posted by. Hitec_Eclipse 7 ◁ Hitec SPECTRA 72 Manual · HPI RS4 Rally Setup ▷. Get HITEC Eclipse 7 Pro Instruction Manual. Get all HITEC manuals!.
|Genre:||Health and Food|
|Published (Last):||3 June 2013|
|PDF File Size:||12.31 Mb|
|ePub File Size:||8.15 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 25 Model Setup Functions 4. Again, you can only select one exponential and they are normally found only on systems costing far more.
What’s missing? Tell us about it.
From the moment you release the button, the receiver will count 5 seconds during that time move all the transmitter sticks and other controls to the desired FAIL-SAFE positions e. If they tilt the swash forwards, press the Cursor Right key once to get hitec eclipse 7 manual the elevator setting menu the numeral 2 will be hitec eclipse 7 manual.
There is no differance in the Tx itself. Tell us what’s missing. There are two different glider modes in the Eclipse 7Pro system. It is commonly used during autorotation, THCV window appears. Crow is not an option with the Eclipse. Press the Cursor Right key once, to get to the elevator travel setting menu. Can,t help with model numbers but can shed some light.
C – Flight Condition Menu Transmitter Input Buttons The buttons are used for different things as follows: Page 25 Model Setup Functions Flashing 4. Are you saying the manual is wrong? Please note that for best results, trimming should be done in hitec eclipse 7 manual conditions.
Page 9 Set-up Use of the Hitec 2. No heading changes B. If you hitec eclipse 7 manual the dual rate amount to zero, you will get no response from that channel, which may cause a crash.
Aircraft Flight Trimming Hitec eclipse 7 manual The following chart may be used to systematically set up and trim a model for straight flight and aerobatic maneuvers.
While both have have dual rates on all three axis aileron, rudder and elevator The Optic eclipes only use two switchs for this therefore the Rudder and elevator is ganged on one switch and cannot be independantly switched like the Eclipse can.
This is both helpful and important, because you can set the throw of each servo, in each direction, so that there is no binding. To change the throttle ratchet, remove the back transmitter power.
Page 11 Set-up Use of the Hitec 2. March February Page 10 Set-up Use of the Hitec 2.
Hitec Eclipse 7 Pro Instruction Manual
You set them up in the Model Setup menus see page?? Release the link button.
Menu Descriptions – Helicopter The Throttle Hold function moves the engine throttle servo to a selected position near idle, and disengages it from the throttle stick. I need to hitec eclipse 7 manual what manuak numbers I need for each, that is: Telemetry system Information When you first turn on your transmitter, the first screen shown below appears on the LCD display. If you are buying a Tx only all you need to specify is if you want the Synth or single frequency module.
HITEC Eclipse 7 User Manual | 48 pages
Activating throttle hold also disables revolution mixing RVMX. Helicopter Setup Instructions With the transmitter switched off, turn on your Flashing transmitter while pressing both of hitec eclipse 7 manual two Edit keys the two keys on the far left. SS dclipse with the Edit Up Down keys press at the same time. Switch transmitter power OFF.
You begin at set point 1, idle. This keys to get to another setup change procedure only can change the software of Eclipse 7 menu, or switch power off. In order to change modeplease adjust Tension Screws and Mode Screws hitec eclipse 7 manual to below figures.